 |
 |
 |
|
Labconco 110410021 4' Protector XStream Laboratory Hood, with 2 Service Fixtures, 208-230V, 50/60Hz
- By-pass airflow design with variable air volume compatibility
- Eco-Foil Air Foil with aerodynamic Clean-Sweep airflow openings
- Cord-Keeper Slots on left and right side of air foil
- Upper Dilution Air Supply
- Glacier white powder-coated steel exterior
- Rear Downflow Dual Baffle System
- Chemical-resistant, fiberglass-reinforced, composite panel liner and baffles with flame spread index less than 25 per ASTM E84. Baffles are removable for cleaning
- Opti-Zone Baffle with tapered slots
- Tempered safety glass vertical-rising sash with cable and pulley
- Powder-coated sash handle with aerodynamic Clean-Sweep openings
- 37.5" (95.3 cm) high sightline from the work surface to the header panel
- Removable front and side panels, and front and interior service access panels for access to plumbing and electrical wiring
- Pre-wired LED lighting with vapor-proof design and ADA-compliant light and blower switches. Lighting is rated for 50,000 hours
- Sash stop located at 18" (45.7 cm) sash opening position
- Powder-coated stainless steel, 12.8" (32.5 cm) ID exhaust connection(s)
The Labconco Protector XStream Laboratory Hood takes containment, safety and energy savings to the extreme. This general chemical, high performance fume hood was independently tested and challenged well beyond the SEFA-1 standards. With a face velocity of 40 fpm and sash fully open, the Protector XStream was subjected to 50 fpm cross drafts, NIH protocol, and tracer gas measurements in the chest of the mannequin. In all scenarios, the Protector XStream allowed 0.00 ppm average level of tracer gas outside the fume hood. Although your safety officer will determine the actual face velocity setting for your laboratory, the ability of this hood to contain under these adverse conditions sets a new standard of safety. Safety is foremost, but energy saving is equally impressive. Although face velocity is a factor, it’s the volumetric rate (CFM) that determines the energy consumption. Operating a 6' Protector XStream at 60 fpm face velocity, with the sash in its fully open position, requires only 690 CFM. Regardless of your desired operating face velocity, the Protector XStream yields the lowest required CFM of any hood.
The Labconco 110410021 4' Protector XStream Laboratory Hood, with 2 Service Fixtures, 208-230V, 50/60Hz includes:
- Two Pre-Plumbed Service Fixtures with Forged Brass Valves
- Power Cord
- Operator's Guide
- Manufacturer's Documentation
- 1 Year Manufacturer's Warranty
- Please Note: Remote Blower, Ductwork, Work Surface, and Base Cabinet or Stand are required for operation and are NOT INCLUDED
Labconco 110410021 4' Protector XStream Laboratory Hood, with 2 Service Fixtures, 208-230V, 50/60Hz Specifications
|
Product Subcategory:
|
General Chemistry
|
|
Nominal Width:
|
4'
|
|
Blower Requirements:
|
Remote blower required
|
|
Conformance:
|
ANSI Z9.5, ASHRAE 110, ASTM E84, CAN/CSA C22.2, CE, NFPA 45, SEFA 1, UL
|
|
Enclosure Height:
|
59.0"
|
|
Exterior Depth:
|
37.7" (95.8 cm)
|
|
Lighting:
|
LED
|
|
Service Fixtures:
|
2
|
|
Style:
|
Benchtop
|
|
Estimated Shipping Weight:
|
440.0 lbs
|
|
Estimated Shipping Weight metric:
|
200.0 kg
|
|
Dimensions:
|
48.0" w x 37.7" d x 59.0" h
|
|
Dimensions metric:
|
121.9 x 95.8 x 149.9 cm
|
|
Electrical:
|
208-230V, 50/60 Hz, 5A
|
|
|
|
 |
|
 |
|
